229 two-piece grounding connectors for shielded and coaxial cable installation method 1. slip outer sleeve over insulation jacket, after stripping. trim braid to within 1/2 of insulation. 2. fan braid by rotating center conductor and slip inner sleeve under braid. 3. position inner sleeve to extend about 1/16 beyond braid. 4. slip one no. 22 or no. 20 ground wire under outer sleeve (front or back), and slide outer sleeve over braid. for daisy chain grounding, two ground wires can be accommodated by selecting the proper size outer sleeve. 5. outer sleeve covers all exposed strands. 6. compress in specified tool. (tool will not release until full compression stroke is completed.) a reliable method for grounding, terminating and insulating shielded and coaxial cable all-around hex compression is applied with a simple tool. the result: a permanent, compression joint. with or without grounding wire (insertable from front or back), reliable grounding of termination is done quickly, neatly, and accurately. the thomas & betts hex compression is a permanent method which has reliably connected literally hundreds of millions of installations in communications, aerospace, electronic, telephone, radio and tv. the termination is completed quickly, neatly, accurately at a greatly reduced production cost. warning : never install on energized wire. 238-254.pdf 3 7/13/2012 11:38:22 am
two-piece grounding connectors for shielded and coaxial cable o.d. inner insulation connector inner sleeve cat. colour military no. code i.d. o.d. spec. no. gsb-046 tin .046 .075 21981-046 gsb-058 yellow .058 .083 21981-058 gsb-063 red .063 .088 21981-063 gsb-071 green .071 .096 21981-071 gsb-080 blue .080 .103 21981-080 gsb-090 orange .090 .113 21981-090 gsb-096 purple .096 .119 21981-096 gsb-101 yellow .101 .124 21981-101 gsb-109 red .109 .131 21981-109 gsb-115 tin .115 .146 21981-115 gsb-124 green .124 .145 21981-124 gsb-128 tin .128 .152 21981-128 gsb-134 orange .134 .156 21981-134 gsb-149 blue .149 .179 21981-149 gsb-156 red .156 .193 21981-156 gsb-165 tin .165 .194 21981-165 gsb-175 green .175 .215 21981-175 gsb-187 yellow .187 .227 21981-187 gsb-194 blue .194 .226 21981-194 gsb-205 orange .205 .245 21981-205 gsb-219 tin .219 .250 21981-219 gsb-225 yellow .225 .256 21981-225 gsb-232 red .232 .263 21981-232 gsb-250 green .250 .281 21981-250 gsb-261 blue .261 .297 21981-261 gsb-266 tin .266 .297 21981-266 gsb-275 orange .275 .306 21981-275 gsb-281 yellow .281 .331 21981-281 gsb-287 tin .287 .327 21981-287 gsb-297 red .297 .335 21981-297 gsb-312 purple .312 .362 21981-312 gsb-348 orange .348 .400 21981-348 gsb-375 blue .375 .406 21981-375 inner sleeve 1. use a measuring tool over the inner conductor insulation. rotate wire to pick up high spots on cable that are non-symmetrica l. 2. add .005 to the diameter of the conductor insulation. select inner sleeve with this i.d. or nearest larger i.d. o.d. inner insulation determine o.d. of inner conductor insulation with measuring tool. inner sleeve-cat. gsb hard bronze inner sleeve is installed under braid. length 5/16 tin plated as standard. 230 238-254.pdf 4 7/13/2012 11:38:22 am
231 two-piece grounding connectors for shielded and coaxial cable non-insulated outer sleeve-cat. gsc connector outer sleeves cat. colour military no. code i.d. o.d. spec. no. non-insulated gsc-101 tin .101 .124 21980-101 gsc-128 blue .128 .152 21980-128 gsc-149 purple .149 .179 21980-149 gsc-156 yellow .156 .193 21980-156 gsc-175 blue .175 .215 21980-175 gsc-187 orange .187 .227 21980-187 gsc-194 red .194 .226 21980-194 gsc-199 tin .199 .235 21980-199 gsc-205 yellow .205 .245 21980-205 gsc-219 green .219 .250 21980-219 gsc-225 purple .225 .256 21980-225 gsc-232 orange .232 .263 21980-232 gsc-261 yellow .261 .297 21980-261 gsc-275 tin .275 .306 21980-275 gsc-281 purple .281 .331 21980-281 gsc-287 blue .287 .327 21980-287 gsc-297 green .297 .335 21980-297 gsc-312 yellow .312 .362 21980-312 gsc-327 tin .327 .372 21980-327 gsc-348 orange .348 .393 21980-348 gsc-359 purple .359 .399 21980-359 gsc-375 yellow .375 .406 21980-375 gsc-405 red .405 .453 21980-405 gsc-415 blue .415 .463 21980-415 gsc-425 tin .425 .475 gsc-460 tin .460 .510 21980-460 gsc-500 green .500 .550 21980-500 insulated gsr-101 tin .101 .124 18121-101 GSR-128 blue .128 .152 18121-128 gsr-149 purple .149 .179 18121-149 gsr-156 yellow .156 .193 18121-156 gsr-175 blue .175 .215 18121-175 gsr-187 orange .187 .227 18121-187 gsr-194 red .194 .226 18121-194 gsr-199 tin .199 .235 18121-199 gsr-205 yellow .205 .245 18121-205 gsr-219 green .219 .250 18121-219 gsr-225 purple .225 .256 18121-225 gsr-232 orange .232 .263 18121-232 gsr-261 yellow .261 .297 18121-261 gsr-275 tin .275 .306 18121-275 gsr-281 purple .281 .331 18121-281 gsr-287 blue .287 .327 18121-287 gsr-297 green .297 .335 18121-297 gsr-312 yellow .312 .362 18121-312 gsr-327 tin .327 .372 18121-327 gsr-348 orange .348 .393 18121-348 gsr-359 purple .359 .399 18121-359 gsr-375 yellow .375 .406 18121-375 gsr-405 red .405 .453 18121-405 gsr-415 blue .415 .463 18121-415 gsr-460 tin .460 .510 18121-460 gsr-500 green .500 .550 18121-500 outer sleeve 1. add .060 to o.d. of inner sleeve selected. use this dimension to select outer sleeve with this i.d. or the nearest larger i.d. 2. use gsc prefix to order non-insulated outer sleeve. use gsr prefix to order nylon insulated outer sleeve. note: all parts are standard tin plated per mil-t-10727a note: inner and outer connector catalogue nos. conform to mil-f-21608. these suffixes are not colour-coded. they are not stock items. add suffix pf for plain finish. add suffix t for tin plate with no colour code. add suffix np for nickel plate. consult regional sales office for delivery and minimum quantities. soft bronze outer sleeve slips over the braid and ground wire. length 1 / 4 " insulated outer sleeve-cat. gsr soft bronze outer sleeve with nylon insulator slips over the braid and ground wire. 238-254.pdf 5 7/13/2012 11:38:22 am
|
